Fluke 5730A Calibration Manual Download Page 82

Page: 82 / 104

5730A

Calibration Manual

AC Voltage Verification Test

The equipment required for this test is listed in Table 14.

Table 14. Equipment Required for AC V Output Level Tests

1. Place the 5790A on top of the Product and connect the equipment as shown

in Figure 15. Other placements of the equipment are fine as long as they can

be connected with the 12 inch cable.

Note

The point of measurement is at the end of the cable and adapter that
connects to the 5790A. It is essential that the cable not be longer
than 12 inches, it can be shorter.

2. Ensure the guard to ground strap on the Product is connected during the

procedure. Also ensure the Product is set to internal Guard (External Guard

OFF). Refresh the EX GRD button on the 5790A by pressing it off and on 3

times, and then leave it on. The green LED is lit when in the ON position. Set

the range on the 5790A to AUTO and connect the Product guard to the

5790A guard using a short heavy lead.

3. Refer to Table 15 and output .600000 mV @1 kHZ and record the reading

under Measured Value.

4. Test the remaining amplitudes and frequencies in Table 15.
5. Verify that the measured values are within the limits given in the Table 15.

1000V RMS MAX

3V RMS MAX

INPUT 1

INPUT 2

SHUNT

GUARD

GROUND

10V PEAK

MAX

WIDEBAND

7V RMS MAX

SHELL FLOATING

10V PEAK MAX

5730A Calibrator

5790A

AC MEASUREMENT
STANDARD

5790A Measurement Standard

External

Sense

OFF

External

Guard

OFF

External

Guard

hhp310.eps

Figure 15. AC Voltage Test Setup

Equipment Model

AC Measurement Standard

Fluke 5790A

BNC(F) to Dual-Banana Plug Adapter (2 required)

Pomona 1269

Coax Cable - RG-58A/U or RG-58C/U with BNC(M)
Connectors, 12 inch Long

Summary of Contents for 5730A









































































































Search results

Summary of Contents for 5730A

Reviews:

Fluke 5730A, Calibration Manual, Page: 82 / 104

Search results

Summary of Contents for 5730A

Reviews: