manualshive.com logo in svg

Fluke 5730A, Calibration Manual, Page: 45 / 104

Share
Download
Fluke 5730A Calibration Manual Download Page 45

 

Multifunction Calibrator 

 

Calibration Procedures 

35 

 
 
 

8.  Reverse the HI and LO connections at the 732B terminals, and push 

Continue

 on the Product to continue the calibration process. 

9.  After this part of the calibration procedure is complete, the Product shows the 

reference shifts and prompts to continue. Touch 

Continue

. The Product 

prompts to refer to the manual for the correct connections and enter the first 

calibration value. 

10. Connect the Product to the 10 k

Ω

 standard as shown in Figure 2 and enter 

the value of the standard using processes similar to those described for dc 

voltage. If the standard is not between 9 k

Ω

 and 11 k

Ω

, an error message is 

shown. Start over from this point with a different 10 k

Ω

 standard. Push 

 on the Product again to continue. 

11. When the internal 10 k

Ω

 reference has been characterized, accept or reject 

the changes that are about to be made to the calibration constant. To reject 

the changes, touch 

Cancel

. Otherwise, touch 

Continue

 to accept and save 

the changes. This lets the calibration process continue. 

Resistance Standard

Calibrator

 

hhp028.eps 

Figure 2. 742A-1 and 742A-10 k External Calibration Connections 

12. Disconnect the 10 k

Ω

 standard, and connect the Product to the 1 

Ω

 standard. 

Enter the value of the 1 

Ω

 standard using processes similarly described for 

the other standards. If the standard is not between 0.9 

Ω

 and 1.1 

Ω

, an error 

message appears, and the user can start over from this point with another 

standard.  

13. Push 

Continue

 to proceed with calibration. 

14. When the internal 1 

Ω

 reference has been characterized, accept or reject the 

changes that are about to be made to the calibration constant. 

Summary of Contents for 5730A









































































































Reviews:

No comments