manualshive.com logo in svg

Fluke 5730A, Calibration Manual, Page: 12 / 104

Share
Download
Fluke 5730A Calibration Manual Download Page 12

5730A 

Calibration Manual 

 
 

2 

 
 
 

•

  Variable phase reference signal output and phase-lock input. 

•

  Interface for the Fluke Calibration 5725A Amplifier. 

•

  Interface for the Fluke Calibration 52120A Amplifier. 

•

  Standard IEEE-488 (GPIB) interface, that complies with ANSI/IEEE 

Standards 488.1-1987 and 488.2-1987. 

•

  EIA/TIA-574 Standard RS-232 serial data interface for remote control of the 

Product. 

•

  Universal Serial Bus (USB) 2.0 high-speed interface device port for remote 

control of the Product. 

•

  Integrated 10/100/1000BASE-T Ethernet port for network connection remote 

control of the Product. 

•

  USB Host port to save calibration reports to a flash drive. 

•

  Extensive internal self-testing and diagnostics of analog and digital functions 

•

  Visual Connection Management output terminals illuminate to help show 

correct cable connection configurations. 

•

  Soft Power - automatic selection of line voltage/frequency.  

•

  LCD Color VGA display with touch panel overlay. 

•

  A traceable calibration procedure for all modes and ranges that requires only 

10 V, 1 

Ω

, and 10 k

Ω

 external standards, with only occasional independent 

verification. 

•

  Automated calibration check that provides added confidence between 

calibration recalls, and data that can be used to document and characterize 

Product performance between calibration recalls. 

 How to Contact Fluke Calibration 

To contact Fluke Calibration, call one of the following telephone numbers: 

•

  Technical Support USA: 1-877-355-3225 

•

  Calibration/Repair USA: 1-877-355-3225 

•

  Canada: 1-800-36-FLUKE (1-800-363-5853) 

•

 Europe: 

+31-40-2675-200 

•

 Japan: 

+81-3-6714-3114 

•

 Singapore: 

+65-6799-5566 

•

  China:  +86-400-810-3435 

•

  Brazil:  +55-11-3759-7600 

•

  Anywhere in the world: +1-425-446-6110 

To see product information or download manuals and the latest manual 

supplements, visit Fluke Calibration’s website at

 

www.flukecal.com

.

 

To register your product, visit 

http://flukecal.com/register-product

.

 

Summary of Contents for 5730A









































































































Reviews:

No comments