Fluke 5730A Calibration Manual Download Page 68

Page: 68 / 104

5730A

Calibration Manual

Table 8. DC Zero Volt Verification

Product Range

Product Setting

DMM Reading

Limits

220 mV

0 mV

0.5

-.010

0.5

2.2 V

0 V

0.8

-.1

0.8

11 V

0 V

-1

22 V

0 V

-1

220 V

0 V

-10

Self-Calibrate a Fluke 752A Divider with a Fluke 8508A as the Null Detector

1. Connect the Product, 752A, and 8508A as shown in Figure 9.
2. Set the 8508A to the 200 mV dc voltage range at 7 digits, filter “ON” and

“FAST” and internal guard (external guard not selected). FAST mode updates

the reading every 1.5 seconds. This lets the reading track the adjustments

but the readings change frequently and it is somewhat noisy. FAST can be

turned off so that the readings are updated every 5.3 seconds.

3. Set the 752A MODE switch to CAL and the CALIBRATE switch to 10:1 +.
4. Set the Product to output 0 mV on the 200 mV range and push



5. Wait for the reading to settle (this can take several minutes) and then zero

the meter using the

Zero Rng

button.

6. Set the Product to output 20 V.
7. Wait for the reading to settle (this can take several minutes) and note the

reading. Set the CALIBRATE switch to 10:1 – and note the reading.

8. If the readings in step 7 are not the same, then adjust the BALANCE control

until they are the same. (see note 4 below)

9. Set the CALIBRATE switch to 10:1+. Adjust the 10:1 CALIBRATE adjustment

until the reading is 0

0.5

10. Set the Product to output 0 mV on the 200 mV range.
11. Set the 752A CALIBRATE switch to 100:1 +.
12. Wait for the reading to settle (this can take several minutes) and then push

the

Zero Rng

button to zero the meter.

13. Set the Product to output 20 V.
14. Wait for the reading to settle (this can take several minutes) and note the

reading. Set the CALIBRATE switch to 100:1- and note the reading.

Summary of Contents for 5730A









































































































Search results

Summary of Contents for 5730A

Reviews:

Fluke 5730A, Calibration Manual, Page: 68 / 104

Search results

Summary of Contents for 5730A

Reviews: