Fluke 5730A Calibration Manual Download Page 6

Page: 6 / 104

5730A

Calibration Manual

Calibrate the Wideband AC Module (Option 5700A-03) ........................ 40

Wideband Flatness Calibration Procedure ............................................ 42

Calibration Check .................................................................................. 43

Develop a Performance History............................................................. 44

Save Calibration Reports ...................................................................... 45

Calibration Shift Results .................................................................... 45

Calibration Check Shift Results ......................................................... 46

Raw Data Results .............................................................................. 46

Full Verification ...................................................................................... 47

Required Equipment for All Tests ...................................................... 47

Warmup Procedure for All Verification Tests ..................................... 47

Determine Specification Limits for other Calibration Intervals ........... 48

Applying Guardbands to Specification Limits .................................... 49

Resistance Verification Test .............................................................. 51

Verify 0

, 1

, and 1.9

............................................................. 52

Verify 10

through 19 M

............................................................ 53

Verify 100 M

................................................................................ 56

DC Voltage Verification Test ............................................................. 56

DC Zero Test ................................................................................. 57

Self-Calibrate a Fluke 752A Divider with a Fluke 8508A

as the Null Detector ....................................................................... 58

DC Voltage Test at Decade Values ............................................... 62

DC Voltage Test at 19 Volts .......................................................... 66

Direct Current Verification Test ..................................................... 68

AC Voltage Frequency Accuracy Test ............................................... 71

AC Voltage Verification Test .............................................................. 72

Alternating Current Verification Test .............................................. 76

2 mA to 2 A Ranges ...................................................................... 77

200

A Range ................................................................................ 78

Wideband Frequency Accuracy Test ................................................. 82

Wideband AC Voltage Module Output Verification ............................ 82

Wideband Output Accuracy at 1 kHz Test ............................................. 83

Wideband Output Flatness Test ............................................................ 84

General Maintenance ............................................................................ 89

Clean the Exterior .............................................................................. 89

Fuse Replacement ............................................................................ 89

Clean the Air Filter ............................................................................. 91

User-Replaceable Parts ........................................................................ 92

Summary of Contents for 5730A









































































































Search results

Summary of Contents for 5730A

Reviews:

Fluke 5730A, Calibration Manual, Page: 6 / 104

Search results

Summary of Contents for 5730A

Reviews: