manualshive.com logo in svg

Fluke 5730A, Calibration Manual, Page: 40 / 104

Share
Download
Fluke 5730A Calibration Manual Download Page 40

5730A 

Calibration Manual 

 
 

30 

 
 
 

Establish Traceability 

To establish traceability through external standards: 

•

  Except for the internal ac/dc transfer standard, the internal check standards 

are directly calibrated by traceable external standards every time the Product 

is calibrated by Artifact Calibration. 

•

  Traceability of the ac/dc transfer standards is done by external verification.  

These confirm the adjustments made during Artifact Calibrations. The internal 

ac/dc transfer standard is never adjusted, so its traceability is not disturbed 

by calibration. Infrequent verification is done by comparing selected ac 

voltage outputs with an external dc voltage standard through an external 

ac/dc transfer standard. Fluke Calibration recommends verification of this 

process every 2 years or according to the policy of your organization. 

•

  Stable parameters, such as frequency flatness, determined more by circuit 

geometry and dielectric constants than time, addressed in the full verification 

procedures. 

Calibration Reports 

The Product stores two sets of calibration constants: the set currently in use and 

the old set from the previous calibration. This gives the Product the ability at any 

time to produce a calibration report of the differences between the present 

settings and the settings that were in effect before the last calibration. The report 

shows changes for each range and function in 

±

ppm of range and in percentage 

of specification limit. Save the report to a USB drive or retrieve it from a host 

computer through either the RS-232, USB device port, Ethernet port, or IEEE-

488 interface. 

Range Adjustment 

After artifact calibration, further fine adjustments can be made to each range. 

Range adjustments are optional and they are not necessary to meet published 

specifications. However, they can help to align the Product closer to in-house 

standards. 
Before a range calibration, first do the Artifact Calibration as described later in 

this manual. This calibrates the ranges that will not be adjusted. It also makes an 

initial adjustment for each range, and supplies flatness corrections for ac 

functions. 

Summary of Contents for 5730A









































































































Reviews:

No comments