Flexim FLUXUS G800 User Manual Download Page 142

Page: 142 / 161

FLUXUS G80x

A Menu Structure

142

UMFLUXUS_G8V4-6-1EN, 2018-10-10

the coefficient memory is being partitioned

SYSTEM settings\Libraries\Extended Library

selection of the displays for the activation of the extended library

Activation of the Extended Library

SYSTEM settings\Dialogs/Menus

selection of the displays for the activation/deactivation or setting of the menu
items in the other program branches

activation of the menu item for the input of the pipe circumference in the pro-
gram branch

Parameter

activation of the menu item for the input of the fluid pressure in the program
branch

Parameter

This display will only be indicated if

SYSTEM settings

Measuring

Gas-

Measuring

is deactivated.

selection of the input mode for the measuring point number in the program
branch

Measuring

(1234)

: digits, point, hyphen

(

↑↓←

→

)

: ASCII editor

setting for the display for the input of the transducer distance in the program
branch

Measuring

•

user

: Only the entered transducer distance will be displayed if the recom-

mended and the entered transducer distances are identical.

•

auto

: Only the recommended transducer distance will be displayed.

recommended setting:

user

selection of the error value delay
•

damping

: The damping factor will be used.

•

edit

: The menu item for the input of the error value delay in the program

branch

Output Options

will be activated.

activation of the display of the alarm state during the measurement

selection of the unit of measurement for the length

selection of the unit of measurement for the temperature

selection whether the absolute pressure p

or relative pressure p

is to be

used

selection of the unit of measurement for the pressure

INIT-resis-

tant

FORMATTING ...

■■■■■■

...

Libraries

↕

Extended Library

Extended Library
off

>ON<

SYSTEM settings

↕

Dialogs/Menus

Pipe Circumfer.
off

>ON<

Fluid pressure
off

>ON<

Meas.Point No.:
(1234) >(

↑↓←

→

Transd. Distance
auto

>USER<

Error-val. delay
damping

>EDIT<

SHOW RELAIS STAT
off

>ON<

Length unit
>[mm]<

[inch]

Temperature
>[°C]<

[°F]

Pressure absolut
off

>ON<

Pressure
>[bar]<

[psi]

Summary of Contents for FLUXUS G800


































































































































































Search results

Summary of Contents for FLUXUS G800

Reviews:

Related manuals for FLUXUS G800

Brands by name

Popular brands

Flexim FLUXUS G800, User Manual

Search results

Summary of Contents for FLUXUS G800

Reviews:

Related manuals for FLUXUS G800

Brands by name

Popular brands