Flexicon PF7 User Manual Download Page 41

Page: 41 / 179

15.3 USB devices

•

Balance

•

Printer

•

Flash drive

•

Keyboard

Connect the USB device to any USB port on the rear of the pump before turning the
power on.

Figure 18 - Successful connection of a Mettler-Toledo ML-T
balance indicated by a white icon on the Screen info bar.
Successful connection of another compatible balance indicated by
a grey icon on the Screen info bar.

Connect a compatible balance to PF7+ to enable the
following:

•

"Start Zero waste batch" on page 91

•

"Auto-recalibration " on page 85

When balance is not attached these options will not be in
the menu.

15.3.1 Compatible devices

Full functionality is only guaranteed for devices on the list
of compatible devices.

For list of compatible devices:

www.wmftg.com/softwareanddevices

Table 6 - USB flash drive specification

USB 2.0

Minimum 2 GB

Maximum 32 GB

FAT32 format

PF7/PF7+ Peristaltic Filler with QC14 Pumphead User Manual

Summary of Contents for PF7




















































































































































































Search results

Summary of Contents for PF7

Reviews:

Brands by name

Popular brands

Flexicon PF7, User Manual

Search results

Summary of Contents for PF7

Reviews:

Brands by name

Popular brands