manualshive.com logo in svg

FLENDER K.A Series, Operating Instructions Manual

Share
Download
FLENDER K.A Series Operating Instructions Manual Download Page 77

5.7.9

Connecting the heating element

Procedure

To connect heating elements to the gear unit, proceed as follows:
1. Check that the heating element connection is not damaged.
2. Install the electrical wiring for the heating elements.

Further information

Further information about the heating can be found in the heating operating instructions in the 

complete documentation for the gear unit.

5.7.10

Connecting the bearing monitoring system

Procedure

To connect the Pt 100 resistance thermometer, proceed as follows:
1. Check that the Pt 100 resistance thermometer connection is not damaged.
2. Install the electrical wiring between the Pt 100 resistance thermometer and the evaluation 

unit. The customer is responsible for providing the evaluation unit.

Further information

Further information about the Pt 100 resistance thermometer can be found in the Pt 100 

resistance thermometer operating instructions in the complete documentation for the gear unit.

5.8

Tightening procedure

5.8.1

Introduction

Bolts

The bolts must have the following properties:
● Made of steel
● Black-annealed or phosphatised
● Lightly oiled (do not add additional oil)

Mounting

5.8 Tightening procedure

REDUREX Gear unit  5200en

Operating Instructions 03/2019

77

Summary of Contents for K.A Series

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands