FLENDER K.A Series Page 60 Operating Instructions Manual Download | Manualshive

Page: 60 / 128

background image

7. Pour concrete into the recesses in the concrete foundation for the foundation blocks.
8. After the concrete has set, tighten the fastening bolts of the foundation blocks with the

specified tightening torque (Page 77).

9. Record the alignment dimensions and keep the report in a safe place together with these

operating instructions.

NOTICE
Damage caused by unevenly tightening the fastening bolts
The gear unit can be damaged by unevenly tightening the fastening bolts.
Evenly tighten the fastening bolts. Ensure that the gear unit is not deformed or distorted when

tightening the fastening bolts.

Mounting on a concrete foundation using anchor bolts

Requirements

The lower side of the gear unit mounting feet must be clean.

Inserting the anchor bolt

The following diagram shows the inserted anchor bolt:

①

Baseplate

⑤

Anchor bolt

②

Support

⑥

Pressure plate

③

Fine-grout concrete

⑦

Wood

④

Raw foundation

⑧

Hexagon nut

Figure 5-4

Inserted anchor bolt

Proceed as follows to insert the anchor bolt:
1. Place the support on the baseplate embedded in the fine-grout concrete.
2. Insert the anchor bolt.

Mounting
5.3 Gear unit mounting

REDUREX Gear unit 5200en

60

Operating Instructions 03/2019

«
...
58
59
60
61
62
...
»

Summary of Contents for K.A Series

































































































































Reviews:

No comments

Related manuals for K.A Series

Giraffe OmniBed

Brand: Ohmeda Pages: 54

Brand: Palazzetti Pages: 112

Brand: NEC Pages: 44

Brand: Tascam Pages: 80

Brand: Tascam Pages: 2

Brand: Walker Pages: 24

Brand: Kawai Pages: 10

Brand: Patlite Pages: 28

Web Ankle Brace

Brand: Darco Pages: 2

Brand: Darkly Labs Pages: 13

Brand: DARAY Pages: 24

Body Armor Night Splint

Brand: Darco Pages: 2

Brand: LaboGene Pages: 59

Brand: Warehouse-lighting Pages: 3

Brand: Eagle Group Pages: 8

Brand: E2S Pages: 5

Brand: Patty-O-Matic Pages: 28

ST60+ SPEED INSTRUMENT

Brand: Raymarine Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands