manualshive.com logo in svg

FLENDER K.A Series, Operating Instructions Manual

Share
Download
FLENDER K.A Series Operating Instructions Manual Download Page 74

5.7.3

Connecting the air‐oil cooler

Procedure

To connect the air-oil cooler to the gear unit, proceed as follows:
1. Electrically connect the pressure monitor.
2. Electrically connect the fan motor.
3. Electrically connect the contamination indicator of the double change-over filter (if present).

Further information

You can find additional information on the water-oil cooler in the water-oil cooler unit operating 

instructions, provided in the complete gear unit documentation.

Note
Observe the information provided in chapter of the Mounted oil supply system with air-oil cooler 

(Page 30).

5.7.4

Connecting the water-oil cooler

NOTICE
Damage to the water-oil cooler
When installing the piping, it is not permissible that the connections of the water-oil cooler are 

subject to force, torque or vibration.

Procedure

To connect the water-oil cooler to the gear unit, proceed as follows:
1. Remove the connecting bushes from the cooling water connection before connecting the 

water-oil cooler.

2. Flush the water-oil cooler to remove any dirt and pollution.
3. Connect up the cooling water inlet and drain lines. Refer to the dimension drawing for the 

direction of flow and the position of the connections.

4. Electrically connect the pressure monitor (only for appropriately equipped gear units).

Mounting
5.7 Connecting components

REDUREX Gear unit  5200en

74

Operating Instructions 03/2019

Summary of Contents for K.A Series

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands