FLENDER K.A Series Operating Instructions Manual Download | Manualshive

Page: 107 / 128

background image

Disposal

10

Disposal of the gear unit

When disposing of the gear unit after its useful life, please observe the following measures:
● Remove operating oil, preservative agents and coolant from the gear unit and dispose of it

according to regulations.

● Dispose of the gear unit parts according to applicable national regulations or recycle them.

Environmental protection

Observe the following environmental protection measures for disposal:
● Dispose of or recycle packaging material according to applicable national regulations.
● When changing the oil, collect the used oil in suitable containers. Use oil-binding agents to

clean up any oil spillages immediately.

● Store preservative agents separately from used oil.
● Dispose of used oil, preservative agents, oil binding agents and oil-soaked cloths according

to the applicable environmental protection regulations.

REDUREX Gear unit 5200en

Operating Instructions 03/2019

107

«
...
105
106
107
108
109
...
»

Summary of Contents for K.A Series

































































































































Reviews:

No comments

Related manuals for K.A Series

Tetrix 351 AC/DC Smart FW

Brand: EWM Pages: 117

Brand: Keiser Pages: 82

Brand: Keiser Pages: 4

Sportsound SSR-200

Brand: Daktronics Pages: 5

ProFire Lightbridge

Brand: M-Audio Pages: 8

Brand: M-Audio Pages: 36

Brand: Maeda Pages: 276

Brand: Nabtesco Pages: 26

Brand: Wasp Pages: 50

Brand: Yamaha Pages: 139

Brand: Yamaha Pages: 19

Brand: Yamaha Pages: 32

Brand: KAM Pages: 5

Brand: Meyer Pages: 100

Rovelight RT-400

Brand: Orlit Pages: 16

Brand: Ground Fault Systems Pages: 26

Brand: Oromed Pages: 64

ikon profile ww

Brand: ADJ Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands