FLENDER K.A Series Operating Instructions Manual Download

Page: 43 / 128

of rotation. In this case, the input shaft of the main gear unit and the main motor simultaneously

also slowly rotate when a flexible coupling is used between the main motor and gear unit.

Note
Electrically interlock the main motor and the auxiliary drive motor so that only one of the two

motors can be switched on.

Note
When driven by the auxiliary drive, then the input shaft of the main gear unit also slowly rotates.

It is not permissible that this rotary motion is prevented. A brake located on the drive side in the

main drive must be opened when driven by the auxiliary drive.

Oil supply for the overrunning clutch

The overrunning clutch is located in an intermediate flange and has a separate oil space. When

the main gear unit is serviced and its oil changed, then the overrunning clutch is also serviced

and its oil changed at the same time.

Description

3.16 Auxiliary drive

REDUREX Gear unit 5200en

Operating Instructions 03/2019

Summary of Contents for K.A Series

































































































































Search results

Summary of Contents for K.A Series

Reviews:

Related manuals for K.A Series

Brands by name

Popular brands

FLENDER K.A Series, Operating Instructions Manual

Search results

Summary of Contents for K.A Series

Reviews:

Related manuals for K.A Series

Brands by name

Popular brands