Fisher Scientific AccuSpin Micro 17 Instructions For Use Manual Download Page 57

Page: 57 / 79

Technical data

Technical data

Component parts

Part / function

Description

Hausing/body

Sheet steel chassis with attached plastic housing and steel reinforcement

Keys and display panel

Keys and display panel covered with easy care protective foil

Operation "Easycontrol"

system

Rotor chamber dimensions (D x
H) (diameter x height):
accuSpin Micro 17
accuSpin Micro 17R

190 mm x 70 mm
200 mm x 75 mm

Chamber

Up to 48 ml of spilled liquids are retained in the chamber and cannot enter the in-
strument.

Lid lock

Automatic locking when the lid is pressed shut

Lid opening

Electromagnetic release via the "open lid" key

when connected to mains

Emergency lid release

Lid release in case of power failure: emergency opening with auxiliary tool.

Summary of Contents for AccuSpin Micro 17
















































































Search results

Summary of Contents for AccuSpin Micro 17

Reviews:

Related manuals for AccuSpin Micro 17

Brands by name

Popular brands

Fisher Scientific AccuSpin Micro 17, Instructions For Use Manual

Search results

Summary of Contents for AccuSpin Micro 17

Reviews:

Related manuals for AccuSpin Micro 17

Brands by name

Popular brands