manualshive.com logo in svg

Fisher Scientific AccuSpin Micro 17, Instructions For Use Manual

Share
Download
Fisher Scientific AccuSpin Micro 17 Instructions For Use Manual Download Page 26

Handling the rotor 

22 

Checking for aerosol-tightness 

The checking of the rotor type and bucket was done 
according to the dynamic microbiological test proce-
dure with regard to EN 61010-2-020 appendix AA. 

The aerosol-tight bio-containment of the rotor mainly 
depends on proper handling! 

 

Check the aerosol-tight bio-containment 
of your rotor whenever necessary! 

 

 

It is very important that all the seals and 
seal-surfaces are carefully inspected for 
wear and damages like cracks, scratches 
and embrittlement! 

 

For a quick test one can check the fixed angle rotors 
according to the following procedure: 

•

 

Slightly grease all seals. 

•

 

Fill the rotor with approx. 10 ml carbon dioxide 
mineral water. 

•

 

Close the rotor according to the respective han-
dling instructions. 

•

 

Due to the shaking, the carbon dioxide of the water 
is released, and an overpressure is built up. Do not 
press the lid simultaneously. 

•

 

Leaks are recognized by humidity release and 
audible disinflation of gas mix. 

•

 

In case of leakage the aerosol-seals have to be 
replaced and the leakage check has to be re-
peated. 

•

 

Dry rotor, rotor lid and lid seal. 

 

  

Summary of Contents for AccuSpin Micro 17
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands