Fisher Scientific AccuSpin Micro 17 Instructions For Use Manual Download Page 11

Page: 11 / 79

Description of the instrument

Description of the instrument

The descriptions apply generally for all instrument
variants.

Pieces delivered

•

Micro-liter-rotor 24 x 1,5 / 2 ml 75003524

•

a special wrench for securing the rotor

•

cable for mains connection

•

this

Manual

Safety systems

The accuSpin Micro 17 and the accuSpin Micro 17R
are equipped with several safety measures:

•

Housing made of highly impact-resistant plastic;

Extra steel armor.

•

Lid with window and lid latch with locking mecha-

nism
You can open the centrifuge lid only when the cen-
trifuge is switched on and the rotor is standing. You
can only start the centrifuge if the lid is properly
locked.

•

Lid emergency release: Only in case of emergency,
e.g. the power supply is interrupted.

(see

chapter

„troubleshooting“)

Do not tamper with the safety systems!

Summary of Contents for AccuSpin Micro 17
















































































Search results

Summary of Contents for AccuSpin Micro 17

Reviews:

Brands by name

Popular brands

Fisher Scientific AccuSpin Micro 17, Instructions For Use Manual

Search results

Summary of Contents for AccuSpin Micro 17

Reviews:

Brands by name

Popular brands