manualshive.com logo in svg

Fisher Scientific AccuSpin Micro 17, Instructions For Use Manual

Share
Download
Fisher Scientific AccuSpin Micro 17 Instructions For Use Manual Download Page 47

Troubleshooting 

  43

Troubleshooting 

Mechanical emergency lid release 

In case of a power failure you cannot open the lid nor-
mally using the electric emergency release. To permit 
unloading even in this case, the centrifuge is equipped 
with a hand operatated lid unlocking system. However, 
you may use this system 

only

 in case of emergency. 

 

 

Rotor can spin at high speed!  
Touching it may cause severe inju-
ries!

 

Always wait for several minutes until 
the rotor has come to a complete 
standstill without deceleration. With-
out power the brake does not func-
tion, and braking takes much longer  

                  than normal! 

 

Should it be necessary to open the lid manually, pro-
ceed as follows using an appropriate/special tool: 

 

 

 

1.  Make sure the rotor stands still. (control window). 

2.  Unplug the mains cord. 

3. Push a small straight wire of a length of approx. 

7cm (e.g. a bended paper clip etc.) through the hole 
located in the middle above the display, at the 
chamber edge.  

 

Summary of Contents for AccuSpin Micro 17
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands