manualshive.com logo in svg

Fisher Scientific AccuSpin Micro 17, Instructions For Use Manual

Share
Download
Fisher Scientific AccuSpin Micro 17 Instructions For Use Manual Download Page 39

Operation 

  35

Removing the rotor 

To remove the rotor you have to proceed in the reserve 
order as at the installation of the rotor.  

In case of contamination you can remove the rotor from 
the drive shaft without opening the aerosol lid. Then 
you can open the removed rotor e.g. in a safety work 
bench and decontaminate it.  

 

1.  Open the centrifuge lid. 

2.  Unscrew the rotor nut with the provided. Turn the 

rotor nut counterclockwise. 

3.  Grab the rotor centrically and carefully pull it per-

pendicularly off the drive shaft. Make sure not to tilt 
it. 

Audible alarm 

Accompanying all error messages, a warning signal is 
given out which can be silenced upon pressing any 
key. 

By default there is an acoustic signal at the end of any 
centrifugation run. You have the possibility to switch off 
this signal. For this, you have to press the „speed/ RCF 
switch key“ 

  while switching on the centrifuge. 

 

Depending on the pre-selected mode the display 
shows the following signs: “

Snd” “on”

 or 

„Snd“ „oF“.

 

By pressing the set keys 

 or 

in the field “time” the 

acoustic signal function can be turned off or on. Sub-
sequently, by pressing the stop key 

 the new setting 

will be activated. 

Summary of Contents for AccuSpin Micro 17
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands