manualshive.com logo in svg

Fisher Scientific AccuSpin Micro 17, Instructions For Use Manual

Share
Download
Fisher Scientific AccuSpin Micro 17 Instructions For Use Manual Download Page 21

Handling the rotor 

  17

Handling the rotor  

Rotor temperature 

 
 

The rotors are only to be used within 
the temperature range from - 9°C to 
+40°C. Pre-tempering in a freezer 
below - 9°C is vorbidden. 

 

 

Lifetime of the rotor 

There is no limitation on the service life of the high 
performance rotors. However please observe the fol-
lowing due to safety reasons: 

 

Rotors and accessories made of 
plastic should not be exposed to 
direct sunlight and UV radiations

. 

If the rotor shows signs of discolor-
ation, deformation or wear, or imbal-
ance it has to be exchanged straight 
away! 

Rotor lid with a spring lock 

Opening 

The rotor lid is held on the central rotor nut integrated 
into the rotor 

  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The rotor lid is opened by pressing the red unlocking-
button in the central handhold of the rotor lid.  

The lid can be lift-off easy. 

Handhold 

Unlocking-button 

Summary of Contents for AccuSpin Micro 17
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands