manualshive.com logo in svg

Fisher Scientific AccuSpin Micro 17, Instructions For Use Manual

Share
Download
Fisher Scientific AccuSpin Micro 17 Instructions For Use Manual Download Page 44

Maintenance and care 

40 

 

5. Treat the rotor and the rotor lid according to the 

instructions given for the disinfectant (soaking in 
liquid or spraying). You must strictly observe the 
specified action times! 

6.  Turn the rotor head down and drain off the disinfec-

tant. Thereafter thoroughly rinse rotor and lid with 
water. 

7.  Dispose of the disinfectant according to valid regu-

lations. 

8.  Aluminum rotors have to be treated with anticorro-

sive protective oil subsequently. 

9.  All seals have to be lubricated again. 

 

Disinfection with bleaching lye 

 

These agents contain highly ag-
gressive hypochlorites and must 
not be used with aluminum rotors!  

 

The following precautionary measures are to be taken 
for extensive protection of the plastic rotors: 

1.  Avoid high temperatures! 

The bleaching solution and the rotor should not be 
warmer than ca. 25 °C. 

2.  Do not let the bleaching solution act longer than 

absolutely necessary! 

3.  After disinfection, rinse the rotor thoroughly with 

distilled water and allow drying. 

4.  All seals have to be lubricated again 

Summary of Contents for AccuSpin Micro 17
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands