with two batteries connected in parallel to the 2 jacks of
the control housing 04:
B
1
-
B
2
:
3. As soon as charging is completed: disconnect the power
cord 13 from the power grid and then disconnect
battery 09 from charger 11.
NOTES
•
Battery 09 may remain in the rucksack during charging
but can also be extracted and charged on another
support.
CAUTION
•
Using a charger other than charger 11 that comes with
the material is prohibited. Failure to observe this
instruction may lead to the premature deterioration of
the battery 09 and in addition to a risk of injury.
•
If battery 09 is not used for 14 days, it automatically
enters "storage" mode. Its voltage drops to about 50%
of full load automatically and its internal consumption is
reduced to a minimum. In this mode, battery 09 can not
be used as is. To exit the "storage" mode, suffices to
connect it to charger 11 in order to be able to use
FELCO 880 POWERPACK correctly.
CHARGER
•
Charger 11 delivered with the tool is intended for
charging exclusively the battery 09 of POWERPACK
FELCO 880.
•
If the output cable of charger 11 supplying battery 09 is
cut or damaged, the entire charger 11 assembly must
be returned to the authorized dealer from whom the tool
was purchased.
•
Charger 11 does not require any special maintenance
but should be in a ventilated area, away from heat, dust
and moisture.
•
If indicator light 12 (red during charging / green when
charged) does not light during charging:
1. Disconnect the power cord 13 from the power grid.
2. Check the power grid by means of plugging in
another device.
3. Reconnect the power cord 13 to the power grid. If
charger 11 remains non-operational, return the
assembly (charger 11, power cord 13 and battery 09)
to the authorized dealer, packed in its original
packaging.
CHANGING THE BATTERY
Battery 09 can be changed at any time through a simple visit
to your dealer and proceeding to the substitution of the
damaged battery with a new one.
CAUTION
Only original FELCO SA batteries can be connected to
control housing 04. FELCO SA shall not accept any
responsibility in case of connection of a battery other than an
original FELCO SA battery. Any injury or damage caused by
the use of a battery that is not an original FELCO SA battery,
is the responsibility and shall be borne by the buyer violating
this clause.
OUTSIDE THE PRUNING PERIOD
•
Store POWERPACK FELCO 880, in its transportation
case 14 away from heat, dust and moisture, in a
conditioned area b10°C (+50°F) and +40°C
(+104°F). Do not place any flammable objects at a
distance less than 1.5 meters from the battery 09.
Ensure that switch 07 is set to "OFF" position.
•
Never store POWERPACK FELCO 880 at an ambient
temperature exc40°C (+104°F).
CAUTION
•
To preserve the longevity of the battery 09 and prevent
its deterioration, it is imperative to store it in charged
condition and recharge it every 12 months when not in
use.
•
Do not operate switch 07 during the storage period.
•
It is recommended, during OFF SEASON period, to
perform a general inspection of your tool, at an
authorized dealer. For more information, consult your
authorized dealer, or contact us.
USB POWER SUPPLY
The control housing 04 is equipped with a USB power
supply connector 05 (Type A IP67) which allows you to
charge small electronic devices such as walkmans, mobile
phones and other mobile accessories. This power supply is
only active when switch 07 is set to "ON". It is not designed
to charge laptops, touch pads and other equipment not
specified above.
REMOTE HOUSING
The remote housing 06 allows you to check the charging
status of your batteries 09 as well as to view statistics,
enable/disable operation options, or perform preliminary
diagnostics in case of breakdowns, or malfunctions.
The operation of the remote housing 06 is very simple and
intuitive (see illustration E on page 5):
PGUP = up
INCR = input
PUSH = input
DECR = output
PGND = down
The commands defined above, are the ones used
systematically in all remote housing 06 menus.
LAUNCHING
When used with a FELCO 801 or a FELCO 820, upon
starting the tool using switch 07 located on the remote
unit 06, the following information is provided on the display, if
the value of the number of cuts until the next service equals 0
or is less than 0.
#
X
X
X
X
X
X
www.kipogeorgiki.gr
www.kipogeorgiki.gr
10
Τηλ
. 210 5573739
