This value provides an indication of the number of cuts that
you can still perform before a service is recommended.
If this value is positive, a few seconds later the display shows
automatically the battery charge level.
If the value is negative, in order to display the batteries
charge levels you must use command PUSH of the remote
housing 06.
When used with FELCO 800 or FELCO 810, upon launching
the tool, the information related to next service is not
available, the display shows automatically the batteries
charge level.
B
1
-
B
2
:
Each block corresponds to 10% of battery capacity, here
battery B1 is 100% full and battery B2 is 100% full.
When battery B1 is 50% and battery B2 is not connected or
empty (0%), the display shows the following:
B
1
-
B
2
:
-
-
-
-
-
-
-
-
-
-
-
-
-
- -
From the battery level display:
B
1
-
B
2
:
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
And using functions "PGND and PGUP" you are able to
intuitively navigate through the menus listed below.
In order to navigate in the various menus, refer to the
following navigation diagrams:
- Use with FELCO 801 or 820: diagram F on page 6
- Use with FELCO 800 or 810: Diagram G on page 123.
NOTES
•
The options, "Semi-open setting", "Standby Mode" and
"Non-progressive mode" are only available if the
POWERPACK FELCO 880 is used with FELCO 801 or
FELCO 820 pruning shears.
MENU "CUT STATISTICS" (FELCO 801, 820, 800 OR 810)
PUSH 2 sec=RESET
Left part # XXXXXX = Number of cuts made since the last
reset of the counter.
Right part XXX h YY m = Time of tool usage in hours and
minutes since the last reset of the counter.
If you press the joystick for 2 seconds (PUSH command), the
2 counters of this screen are reset to zero.
"CUT TYPES" MENU (FELCO 801, 820, 800 OR 810)
PUSH 2 sec=RESET
S (SMALL) = Percentage of small diameter cuts,
M (MEDIUM) = Percentage of medium diameter cuts,
L (LARGE) = Percentage of large cuts
performed since the last counter reset. The different levels of
cuts classifications are determined on the basis of the
averages and these values should be considered as an
indication.
If you press the joystick for 2 seconds (PUSH command), the
3 counters of this screen are reset to zero.
"BLOCKAGE" MENU (FELCO 801, 820, 800 OR 810)
PUSH 2 sec=RESET
XX% XXL = Percentage of cutting head blockages since the
last reset of the counter. Shows whether the diameters of
wood cut correspond to the capacity of the tool and whether
the tool is used properly.
If you press the joystick for 2 seconds (PUSH command), the
counter of this screen is reset to zero.
"SEMI-OPENING SETTING" MENU (FELCO 801 AND
FELCO 820 ONLY)
POWERPACK FELCO 880 is factory set to switch cutting
head to semi-opening mode when pressing 2 times rapidly
on the trigger 16 of the tool. To return to full opening mode,
simply press the trigger 16 again 2 times, quickly. The 4
displays below allow you to choose the type of semi-opening
mode desired with the tool (50%, 60% or 70%), or to disable
this option.
1
/
2
5
0
%
O
N
Indicates that semi-opening mode is set to 50% of the total
opening range of the cutting head. This is the factory setting.
PUSH
1
/
2
6
0
%
O
N
If you press PUSH, semi-opening mode of the blade 17
toggles from 50% to 60%. Indicates that semi-opening mode
is set to 60% of the total opening range of the cutting head.
PUSH
1
/
2
7
0
%
O
N
If you press PUSH, semi-opening mode of the blade 17
toggles from 60% to 70%. Indicates that semi-opening mode
is set to 70% of the total opening range of the cutting head.
Semi-opening mode is deactivated by means of pressing the
joystick, PUSH command.
PUSH
1
/
2
O
F
F
"STAND BY MODE" MENU (FELCO 801 AND FELCO 820
ONLY)
C
L
I
C
K
-
C
L
I
C
K
O
N
PUSH
C
L
I
C
K
-
C
L
I
C
K
O
F
F
CLICK-CLICK ON = POWERPACK FELCO 880 is factory
set, for the "stand-by" mode of the pruning shear FELCO 820
to be activated in pressing the trigger 16 two times rapidly
and holding the trigger 16 until a triple rapid audio signal
#
1
2
3
4
5
6
/
1
2
3
h
4
5
m
4
2
%
S
3
7
%
M
2
1
%
L
- -
%
X
X
L
www.kipogeorgiki.gr
www.kipogeorgiki.gr
11
Τηλ
. 210 5573739
