manualshive.com logo in svg

FEDCO MSD-160, Installation & Operation Manual, Page: 56 / 66

Share
Download
FEDCO MSD-160 Installation & Operation Manual Download Page 56

MSD

TM

 Series

© Copyright 2018 Fluid Equipment Development Company | www.fedco-usa.com

- 

56

 -

Specifications

Recommended Spare Parts List

1-3 years of service

Refer to 

Maintenance Schedule

 

and the 

Service Parts Kits

 chart on the following two pages of 

this manual.

5 years of service

A complete disassembly, cleaning and inspection of all pump components is recommended. Re

-

fer to the 

Service Parts Kits

 chart on the following two pages of this manual.

Service Parts Kits

Refer to the 

Service Parts Kits

 chart on the following two pages of this manual.

NOTES: 

Please provide pump serial number when ordering field service kits.

Ordering 

Parts

To order a component or service kit, simply contact a FEDCO representative at:

ATTN: Field Service Department

FEDCO

800 Ternes Drive

Monroe, MI 48162

USA

Additional Contact Information:

Tel    

734-241-3935

Fax    

734-241-5173

Email   

[email protected]

  [email protected]

Web site   www.fedco-usa.com

Choose the “Service and Support” tab

Summary of Contents for MSD-160



































































Reviews:

No comments