manualshive.com logo in svg

FEDCO MSD-160, Installation & Operation Manual, Page: 50 / 66

Share
Download
FEDCO MSD-160 Installation & Operation Manual Download Page 50

MSD

TM

 Series

© Copyright 2018 Fluid Equipment Development Company | www.fedco-usa.com

- 

50

 -

Pump Assembly Continued

Inlet Piping

Keep the inlet pipe free of high points which could trap air and could disrupt pump priming. Vac-

uum and/or pressure gages are recommended to allow measurement of pump inlet pressure. 

NEVER throttle the pump on the inlet side. 

Outlet Piping

The pump discharge piping should have a removable section of pipe such as a spool piece or 

elbow to allow the pump to slide forward for service.  Servicing the shaft seal, water bearing or 

flexible coupling requires a space of approximately 30.5 cm (12 inches) minimum. The pump as

-

sembly must be free to move away from the motor in order to gain access to these components.

REMOVABLE SECTIONS 

FOR PUMP SERVICE

OUTLET PIPING

DISCHARGE HOUSING

30.5 cm

 (12 in)

MINIMUM

OR

Figure 96 - 

Removable Section 

For Pump Service

Summary of Contents for MSD-160



































































Reviews:

No comments