manualshive.com logo in svg

FEDCO MSD-160, Installation & Operation Manual, Page: 44 / 66

Share
Download
FEDCO MSD-160 Installation & Operation Manual Download Page 44

MSD

TM

 Series

© Copyright 2018 Fluid Equipment Development Company | www.fedco-usa.com

- 

44

 -

Pump Assembly Continued

  .125

3.18

 

  .125

3.18

 

Figure 84 - Installing Dropout Coupling Set 

Screw

Figure 83 - 

Joining Coupling Hubs

Figure 82 - Dropout Coupling Cross Section

14. Install the dropout coupling set screw and 

tighten to torque specs found in the 

Fas-

tener Torque Specifications

 section of this 

manual.

NOTES: 

Set screws are only on the motor side 

of the dropout coupling. NO set screws should 

be installed on the pump shaft side of the cou

-

pling.

13. 

Join the motor hub with the dropout hub us

-

ing hardware removed in step 2.

NOTES: 

If indicating pump using the 

Reverse 

Indicator 

or a 

Laser Alignment Tool Method, 

tighten dropout coupling set screw and initiate 

alignment process. Upon completion, remove 

coupling and alignment bushing as described 

in step 1. Re-install dropout coupling and pro-

ceed with next step.

NOTES: 

Remove alignment bushing before 

operation.

NOTES: 

Cross section for reference only.

Summary of Contents for MSD-160



































































Reviews:

No comments