manualshive.com logo in svg

FEDCO MSD-160, Installation & Operation Manual, Page: 16 / 66

Share
Download
FEDCO MSD-160 Installation & Operation Manual Download Page 16

MSD

TM

 Series

© Copyright 2018 Fluid Equipment Development Company | www.fedco-usa.com

- 

16

 -

Installation Procedures Continued

Foundation Specifications 

A concrete foundation is recommended for 

all MSD pump installations. Concrete provides 

good support and good vibration absorption. 

The foundation should have a mass that is 

50% more than the total weight of the equip-

ment and its perimeter should extend at least 

6 inches (15 cm) on each side from the pump 

and motor. Make sure the concrete is com-

pletely dry and level before installing any ma

-

chinery. Make sure anchor bolts and shims are 

properly sized and installed in cases of uneven 

surfaces.

LEVELING BOLTS

VERTICAL

BASEPLATE

PROPER SHIM PLACEMENT

(Shims are optional with alignment kit. Anchor bolts are not provided)

CONCRETE 

FOUNDATION

Figure 18 - 

Proper Shimming Uneven (Vertical)

LEVELING BOLTS

OPTIONAL BASEPLATE

PROPER SHIM PLACEMENT

(Shims are optional with alignment kit. Anchor bolts are not provided)

CONCRETE FOUNDATION

Figure 19 - 

Proper Shimming Uneven (Horizontal)

Summary of Contents for MSD-160



































































Reviews:

No comments