Fcar FD505 User Manual Download Page 16 | Manualshive

Page: 16 / 73

background image

FCAR FD505 Wheel Alignment System User Manual

16

3)

Rotate the hand wheel again to adjust and lock the clamp to the rim position.

Figure 3.2-1 Fixture installation

The physical photo is shown below:

Note: When assembling the fixture, the claws should keep away from the lead

block on the rim, please make sure that the four claws are in full contact with the

rim.

Installed long and short target object as shown below:

«
...
14
15
16
17
18
...
»

Summary of Contents for FD505










































































Reviews:

No comments

Related manuals for FD505

Brand: Faderfox Pages: 8

Brand: dbx Pages: 12

Brand: dbx Pages: 13

Brand: dbx Pages: 72

Brand: dbx Pages: 11

Brand: dbx Pages: 16

Brand: EASTERN INSTRUMENTS Pages: 93

Brand: Pari Pages: 2

PowerXL DX-NET-ETHERNET2-2

Brand: Eaton Pages: 48

Power Xpert C445

Brand: Eaton Pages: 2

Brand: Labnet Pages: 12

Accublock D1301

Brand: Labnet Pages: 13

Brand: Qlight Pages: 3

Brand: qtran Pages: 2

Brand: Q-Optics Pages: 2

Brand: Waterpik Pages: 2

Brand: Yacht Devices Pages: 32

Brand: Meritor Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands