Fayat Group Bomag BVT 65 Operating Instruction, Maintenance Instruction Download

Page: 78 / 97

8.7.4.2

Adjusting the engine speed

Protective equipment:

Working clothes

Protective gloves

Park the machine in secured condition

Chapter 6.4 ‘Park

the machine in secured condition.’ on page 55

Disassemble the left engine guard.

WARNING!
Danger of burning on hot components!

Wear your personal protective outfit (protective

gloves, protective clothing).

Adjust the idle speed using the stop screw (2) on the throttle

lever.

Adjust the maximum speed via the stop screw (1).

Secure the stop screws with counter nuts.

Adjust the throttle cable, if this should be neces-

sary.

Assemble the left hand engine guard again.

Fig. 74

Fig. 75

Fig. 76

Maintenance – Annually

BVT 65

Go to

Discount-Equipment.com

order your parts

Summary of Contents for Bomag BVT 65


































































































Search results

Summary of Contents for Bomag BVT 65

Reviews:

Related manuals for Bomag BVT 65

Brands by name

Popular brands

Fayat Group Bomag BVT 65, Operating Instruction, Maintenance Instruction

Search results

Summary of Contents for Bomag BVT 65

Reviews:

Related manuals for Bomag BVT 65

Brands by name

Popular brands