Fayat Group Bomag BVT 65 Operating Instruction, Maintenance Instruction Download

Page: 24 / 97

3.4.3 Safety regulations and environmental protection regulations for handling gas-

oline

DANGER!
Danger to life caused by explosive gas-air mixes!

–

Do not allow gasoline to come into contact with hot

components.

–

Smoking and open fire is prohibited.

–

Keep away from heat sources, sparks and other

sources of ignition.

–

Do not spill any gasoline.

WARNING!
Health hazard caused by contact with gasoline!

–

Wear your personal protective outfit (protective

gloves, protective clothing).

–

Do not inhale any fuel fumes.

–

Do not swallow gasoline.

–

Avoid contact with gasoline.

ENVIRONMENT!
Gasoline is an environmentally hazardous sub-

stance!

–

Always keep gasoline in proper containers.

–

Immediately bind spilled gasoline with an oil-

binding agent and dispose of in accordance with

regulations.

–

Dispose of gasoline and fuel filter according to reg-

ulations.

Fig. 5

Concerning your safety – Handling fuels and lubricants

BVT 65

Go to

Discount-Equipment.com

order your parts

Summary of Contents for Bomag BVT 65


































































































Search results

Summary of Contents for Bomag BVT 65

Reviews:

Related manuals for Bomag BVT 65

Brands by name

Popular brands

Fayat Group Bomag BVT 65, Operating Instruction, Maintenance Instruction

Search results

Summary of Contents for Bomag BVT 65

Reviews:

Related manuals for Bomag BVT 65

Brands by name

Popular brands