Fayat Group Bomag BVT 65 Operating Instruction, Maintenance Instruction Download

Page: 67 / 97

8.6.2 Cleaning, checking the spark plug, replacing if necessary

NOTICE!
Danger of engine damage!

–

Do not use spark plugs with incorrect heat value.

Recommended spark plugs:

NGK

CR5HSB

DENSO

U16FSR-UB

Protective equipment:

Working clothes

Protective gloves

Special tool:

16 mm spark plug spanner

Park the machine in secured condition

Chapter 6.4 ‘Park

the machine in secured condition.’ on page 55

Allow the engine to cool down for at least 15 minutes.

Pull off the spark plug socket (1).

Clean the area around the spark plug.

Unscrew the spark plug with a 16 mm spark plug spanner

(2).

Check the condition of the spark plug, clean if necessary.

In case of excessive combustion residues or burned off elec-

trodes replace the spark plug.

Check the electrode gap of the spark plug with a feeler

gauge, if necessary adjust the gap.

Nominal value:

0.6 - 0.7 mm (0.024 - 0.028 in)

Turn the spark plug carefully in by hand.

10.

Once the sealing surface of the new spark plug is in contact

tighten for another 1/2 turn with the spark plug spanner.

11.

Once the sealing surface of the used spark plug is in contact

tighten for another 1/8 to 1/4 turn with the spark plug

spanner.

Fig. 46

Fig. 47

Maintenance – Monthly

BVT 65

Go to

Discount-Equipment.com

order your parts

Summary of Contents for Bomag BVT 65


































































































Search results

Summary of Contents for Bomag BVT 65

Reviews:

Related manuals for Bomag BVT 65

Brands by name

Popular brands

Fayat Group Bomag BVT 65, Operating Instruction, Maintenance Instruction

Search results

Summary of Contents for Bomag BVT 65

Reviews:

Related manuals for Bomag BVT 65

Brands by name

Popular brands