manualshive.com logo in svg

Farmet MONSUN MC, Operating Manual, Page: 9 / 58

Share
Download
Farmet MONSUN MC Operating Manual Download Page 9

 

 

Manual

 

MONSUN MC | ME 

9 

│

 58 

-

 

warn persons not to approach the machine and the tractor. 

-

 

wait for the arrival of professional rescue team. 

Never stand on the machine under power lines. The voltage can be transferred even without direct 
contact.  
 
Checking the surroundings 
Check the nearest surroundings of the machine before starting, unfolding and operation. Always pay 
attention to have a sufficient view. Do not drive the machine until there are no objects or people in 
its surroundings. Using the machine without checking the surroundings can cause accidents. 
 
Tightening bolts and nuts 
Regularly check tightening of bolts and nuts. Due to the use of the machine, the individual bolts may 
loosen unnoticed. Tighten bolts and nuts as needed. 
 
Failure procedure  
In case of a failure of a part of the machine, immediately stop and secure the machine. Immediately 
remove the failure or call the service. Continued use of the machine can cause its serious damage or 
accidents.  
 

Disconnecting the machine 

 
Increased risk of injury 
There is an increased risk of injury when disconnecting the machine.  
In order to avoid risky situations: 

-

 

secure the tractor against any movement, 

-

 

never stand between the tractor and the machine when disconnecting, 

-

 

control the three-point lifting device slowly and carefully. 

-

 

pay attention to flat and safe location of the machine, 

-

 

disconnect hydraulic hoses only when the hydraulic system is without any pressure. 

Failure to observe these rules can result in serious or fatal incident. 
 

Servicing and maintenance 

 
Observe service and maintenance intervals 
Observe prescribed check intervals as stated in the operating manual. Failure to do so can cause a 
damage to the machine, wrong work quality or accident. 
 
Use original spare parts only. 
Many parts have specific properties which are important for the machine stability and function. Only 
spare parts and accessories supplied by the manufacturer are tested and approved. Other products 
can impair the machine function or affect its safety. When using other than original spare parts the 
product warranty and responsibility of the manufacturer expires.  
 
For all works related to the maintenance: 

-

 

switch off the input shaft of tractor, 

-

 

release the pressure from the hydraulic system, 

-

 

if possible, disconnect the tractor, 

-

 

pay attention to safe site of the machine, support it when needed, 

-

 

when leaving the machine, do not stand on the machine but use safe steps, 

-

 

secure the machine against movement, 

Summary of Contents for MONSUN MC



























































Reviews:

No comments