manualshive.com logo in svg

Farmet MONSUN MC, Operating Manual, Page: 55 / 58

Share
Download
Farmet MONSUN MC Operating Manual Download Page 55

 

 

55 

│

 58 

Manual

 

MONSUN MC | ME 

Hydraulics 

Defect 

Cause 

Remedy 

The fan 
revolutions are 
not sufficient. 

Small section of the supply 
line, incorrect size of 
connectors. 
 
lack of oil 
 
high pressure in the 
feedback 

Choose the supply line with sufficient 
section and large connectors. 
 
 
Check and fill the oil. 
 
Check the oil filter, use connectors 
with larger section. 

Oil leakage in 
hydraulic motor. 

Worn shaft sealing or 
incorrectly mounted. 

Replace the sealing. 

Fan revolutions 
are insufficient. 

Incorrectly set three-way 
valve. 
 
Insufficient volume or 
pressure of oil. 

Check the setting of the three-way 
valve. 
 
Check the valve for pressure limiting. 

High 
temperature of 
hydraulic oil. 

Oil flow need to be 
regulated on the tractor. 
 
 
The three-way valve is set 
as the two-way valve. 

Fully open the three-way valve to 
adjust the flow on the machine and 
regulate the oil flow on the tractor. 
 
Correctly set the three-way valve. 

Hydraulic motor 
shortly halts. 

Too little oil. 

Fill the oil. 

The marker folds 
too much 
quickly.  

Missing throttle pad in the 
hydraulic system 
 
The flap in the hydraulic 
system is overdesigned. 

Ask for mounting of a washer. 
 
 
Ask for the replacement of the 
throttle valve.  

The marker folds 
too much slowly 
or not at all. 
 

The flap in the hydraulic 
system is clogged. 
 
The flap in the hydraulic 
system is underdesigned. 

Ask for the flap cleaning. 
 
 
Ask for the replacement of the 
throttle valve.  

Both markers 
open 
simultaneously. 

The switching valve is 
wrong. 

Let the switching valve get replaced. 
 

The marker of 
tramlines des not 
move. 

The flap in the hydraulic 
system is clogged. 

Ask for the flap cleaning.  
 
 

Both markers 
open 
simultaneously. 

The switching valve is 
wrong. 

Let the switching valve get replaced. 

The marker of 
tramlines des not 
move. 

The flap in the hydraulic 
system is clogged. 

Ask for the flap cleaning.  
 
 

 
 

Summary of Contents for MONSUN MC



























































Reviews:

No comments