Farmet MONSUN MC Operating Manual Download Page 10 | Manualshive

Page: 10 / 58

Farmet MONSUN MC Operating Manual Download Page 10

Manual

MONSUN MC | ME

10

│

58

-

in no case touch the running V-belt.

Disconnection of the power supply
Before any work with electric equipment the power supply disconnection is necessary. Working on
live equipment can cause an injury and damage the machine.

Replacement of hydraulic hoses
Hydraulic  hoses  shall  be  replaced  every  three  years  as  they  age  without  visible  external  damage.
Damaged hoses can cause serious or fatal injuries.

Cleaning with high-pressure cleaner
The machine can be cleaned with water or vapor jet. Clean bearings, fans, signal distributors, plastic
parts and hydraulic hoses under only light pressure to avoir their damage.

Disconnect the accumulator and the alternator before welding
Disconnect  the  accumulator  and  the  alternator  before  electric  welding.  Thus  any  damage  to
electronic device can be avoided.

Tightening of bolt joints
After service and maintenance work tighten the loosened screws again. Untightened screw joints can
cause injuries and material damage.

Checking the pressure in tires
The pressure in tires shall be regularly checked.

o

7.50x16 8PR -

4,5 bar

o

23x8.50-12 6PR -

3,5 bar

o

31x15.5-15 8PR-

3,1 bar

Other regulations

Compliance with regulations

In addition to these safety instructions follow also following regulations:

-

safety regulations,

-

general rules of safety, health protection in work and road traffic,

-

instructions in this operating manual,

-

regulation for operation, maintenance and service.

«
...
8
9
10
11
12
...
»

Summary of Contents for MONSUN MC



























































Reviews:

No comments