Farmet MONSUN MC Operating Manual Download Page 44 | Manualshive

Page: 44 / 58

Farmet MONSUN MC Operating Manual Download Page 44

44

│

58

Manual

MONSUN MC | ME

Never start the fan if you are not sure with correct sensor setting. This can permanently
damage the sensor.



Check a smooth rotation of the shaft without touching the sensor. Carefully manually turn the fan.

The shaft shall not touch the sensor but should invoke to impulses per one revolution. The groove
provides a switching impulse when passing the sensor, the diode on the sensor blinks.



Tighten the nut on the sensor.

Setting of the fan sensor.

Hydraulic hoses

Hydraulic hoses get worn and age without visible external signs. Based on valid international
regulations the hydraulic hoses need to replaced every 6 years.

Ensure the hoses are without pressure when changing them.

Replacement of harrow fingers



Release screws and nuts.



Replacement of the harrow.



Fix the harrow handle and firmly tighten.

Replacement of harrow fingers

Sensor with light diode

Cam

Sensor with

light diode

Belt

Nuts

Harrow

«
...
42
43
44
45
46
...
»

Summary of Contents for MONSUN MC



























































Reviews:

No comments