Farmet MONSUN MC Operating Manual Download Page 17 | Manualshive

Page: 17 / 58

Farmet MONSUN MC Operating Manual Download Page 17

17

│

58

Manual

MONSUN MC | ME

A-

Supply to the hydraulic motor

B-

Hydraulic motor outlet

P- Supply

T- Outlet

Adjusting three-way/two-way valve of the hydraulic motor

Markers operating

The marker exceeds the working width of the machine by a half. Take extra care to

obstacles and persons in the surroundings.



setting of markers length Chapter Preparation on the field



Setting of marker

The marker is used to mark the track of following run. Markers are hydraulically controlled and are
alternately switched using the pressure and the switch over valve.

Unfolding the marker:



Check that the hydraulic hoses couplings are tight and that the machine is unfolded in working

position,



activate the marker using the lever in the tractor.

Then the marker unfolds.

Folding the marker:



Activate the marker by pulling the lever in the opposite direction then for unfolding.

Then the marker shall fold.

Repeating this procesure the second marker shall be activated. Thus both markers are alternately
controlled using one hydraulic circuit.

The pressure switch over valve is based on an alternate switching of two outlets using
the reverse pressure. It is not necessary to make the whole piston stroke for switching
over which fits for by-passing of obstacles.

When working pay attention to persons around the marker. Nobody can be
near or under the marker when it is folded or unfolded.

A

P

B

T

Adjusting screw

Locking nut

Screw

«
...
15
16
17
18
19
...
»

Summary of Contents for MONSUN MC



























































Reviews:

No comments