manualshive.com logo in svg

Farmet MONSUN MC, Operating Manual, Page: 31 / 58

Share
Download
Farmet MONSUN MC Operating Manual Download Page 31

 

 

31 

│

 58 

Manual

 

MONSUN MC | ME 

Heavy soils = inclined disc (set the inclination angle as needed) 
 
Light soils = vertical disc (no setting of the inclination angle, or there is only a minor inclination). 
 
Set  the  marker  disc  inclination  so  that  the  marker  traces  are  well  visible  in  the  soil  later.  Markers 
shall not grub. 

 

Setting of marker angle 
 

Release screws. 

 

Set the angle as needed. 

 

Tighten screws. 

 

Setting of pre-emergence markers of tramlines 

 

The  marker  of  pre-emergence  tramlines  creates  tramlines  for  sprayer.  The  hydraulic  valve  is 
controlled  based  on  tramlines  of  Drillmat  III.  The  arm  starts  always  when  the  sowing  sections  are 
locked with flaps. 
 
The marker with two skives is determined for modes in which both tramlines are made during one 
run. 
 
The marker with one skive is determined for modes in which both tramlines are made during the run 
there and back. 

 

Pre-emergence markers  

Pre-emergence 

markers 

Screws 

Summary of Contents for MONSUN MC



























































Reviews:

No comments