manualshive.com logo in svg

Farmet MONSUN MC, Operating Manual, Page: 47 / 58

Share
Download
Farmet MONSUN MC Operating Manual Download Page 47

 

 

47 

│

 58 

Manual

 

MONSUN MC | ME 

Marker 

 
The  maintenance  of  the  shear  screw  on  markers  is  made  in  the  machine  working  position  with 
unfolded marker. This is valid for seed drills MC. 
 
Check the shear screw on the marker arm if it is not damaged, replace it if needed.  

 

Unfold the marker arm. 

 

Remove residuals of damaged shear screw. 

 

Replace the new shear screw. 

 

Tighten it with the self-locking nut.  

Marker disc  
 
Check any damage to the marker disc and replace if needed. 
 

 

Release screws. 

 

Replace the marker disc. 

 

Put screws back and tighten them. 
 

 

Marker disc 

Loosener  

 
The maintenance of the loosener is made in the machine working position. Check skives for wear and 
replace if needed.  
 

 

Release the nut and replace the screw. 

 

Turn the skive or insert a new one. 

 

Fix a new screw and secure it with the nut. 

 
 

Screws 

Marker disc 

Summary of Contents for MONSUN MC



























































Reviews:

No comments