Fabtech FTS24084BK Installation Instructions Manual Download

Page: 30 / 31

65. Install tires and wheels and torque lug nuts to wheel

manufacturer’s specifications. Turn front tires left to right
and check for appropriate tire clearance.

Note - Some

oversized tires may require trimming of the front
bumper & valance.

66. Check front end alignment and set to factory

specifications. Readjust headlights.

67. Recheck all bolts for proper torque.

68. Recheck brake hoses, ABS wires and suspension parts

for proper tire clearance while turning tires fully left to
right.

69. Check the fluid in the front and rear differential and fill

if needed with factory specification differential oil.

Note

- some differentials may expel fluid after filling and
driving. This can be normal in resetting the fluid level
with the new position of the differential/s.

70. Install Driver Warning Decal. Complete product

registration card and mail to Fabtech in order to receive
future safety and technical bulletins on this suspension

Vehicles that will receive oversized tires should check ball

joints and all steering components every 2500-5000 miles

for wear and replace as required.

RETORQUE ALL NUTS, BOLTS AND LUGS

AFTER 50 MILES AND PERIODICALLY

THEREAFTER.

For technical assistance call: 909-597-7800

FIGURE 130

FIGURE 131

FIGURE 132

S.A.E. Bolt Torque Specification Chart

Grade 5

Grade 8

Metric

STANDARD

METRIC

Grade

8.8

Grade

10.9

SIZE

ft. lbs.

SIZE

ft. lbs.

1/4"

M-6

5/16"

M-8

3/8"

M-10

7/16"

M-12

100

1/2"

127

M-14

100

160

9/16"

129

184

M-16

150

240

5/8"

179

254

M-18

200

300

3/4"

317

450

M-20

300

400

30 of 31

Summary of Contents for FTS24084BK
































Search results

Summary of Contents for FTS24084BK

Reviews:

Related manuals for FTS24084BK

Brands by name

Popular brands

Fabtech FTS24084BK, Installation Instructions Manual

Search results

Summary of Contents for FTS24084BK

Reviews:

Related manuals for FTS24084BK

Brands by name

Popular brands