Fabtech FTS24084BK Installation Instructions Manual Download | Manualshive

Page: 24 / 31

background image

48. FT503014 & FT503015 Rear Pocket Nut Tabs & insert into

the tab into the hole just below the body mount. Insert
the 1/2” bolt with the split & flat washer with the supplied
thread-locking compound. Leave loose.

SEE FIGURE 100-101.

49. Remove the rear Trac Bar from the Jeep. Remove any

paint, dirt, or debris from the axle housing where the new
gussets are to be installed.

50. Locate FT50362 Gusset, position it onto the axle and

the factory trac bar mount as shown in photo. Weld the
gusset on the two sides.

SEE FIGURE 102.

51. Locate FT50342 Rear Trac Bar Bracket, position it onto

the top of the axle and trac bar mount. Use the supplied
9/16” bolt to align the new bracket to the original mount.
Use a punch and mark the factory mount through the two
holes in the new bracket. Use a drill with a 3/8” bit and
drill the two new holes. Locate and install the supplied
3/8” hardware. Weld the gusset as shown in the photos.

SEE FIGURES 103-109.

FIGURE 99

FIGURE 100

FIGURE 101

FIGURE 102

FIGURE 103

WELD HERE

NEW SUPPLIED

9/16” HARDWARE

TRAC BAR INSTALLED FOR PHOTO ONLY, IT

MUST BE REMOVED PRIOR TO INSTALLATION.

24 of 31

«
...
22
23
24
25
26
...
»

Summary of Contents for FTS24084BK
































Reviews:

No comments

Related manuals for FTS24084BK

Brand: Lauterbach Pages: 67

Oakville Series

Brand: Napoleon Pages: 72

Brand: Napoleon Pages: 4

Allure Vertical Series

Brand: Napoleon Pages: 120

Brand: Velleman Pages: 2

Brand: Velleman Pages: 9

Brand: Panasonic Pages: 18

Brand: Jabra Pages: 2

Brand: Fenix Pages: 4

Brand: J.Burrows Pages: 4

Brand: Sierra Monitor Corporation Pages: 1

Brand: Home Accents Holiday Pages: 2

Brand: Metra Electronics Pages: 4

REARSIGHT OnStar 250-8822

Brand: Rostra Pages: 2

Brand: Empire Comfort Systems Pages: 4

Brand: Edelbrock Pages: 1

Brand: FORM FIT Pages: 2

Brand: Nippon Gases Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands