Fabtech FTS24084BK Installation Instructions Manual Download | Manualshive

Page: 10 / 31

background image

18. Locate FT50390BK Crossmember, FT50314 & FT50315

Nut Tabs, and the supplied 1/2” & 12mm hardware.
Attach ** the front tabs of the crossmember to the factory
lower pockets with the 1/2” hardware & leave loose.
Rotate the crossmember up to the bottom of the frame
and attach with the supplied 12mm bolts with flat & split
washer.

SEE FIGURES 26-28.

19. Mark & drill the bottom frame for the rear hole on the new

crossmember. Use a small drill bit first and follow with a
1/2” bit. Locate FT50314 & FT50315 Nut Tabs, 1/2” x 1
1/2” bolts with flat & split washers. Insert the nut tab into
the frame and attach** with the 1/2” hardware.

SEE FIGURES 29-32.

FIGURE 26

FIGURE 29

FIGURE 30

10 of 31

FIGURE 27

FIGURE 28

FIGURE 25

«
...
8
9
10
11
12
...
»

Summary of Contents for FTS24084BK
































Reviews:

No comments

Related manuals for FTS24084BK

Brand: 3M Pages: 26

Brand: Zen Underwater Pages: 3

Brand: ICON Pages: 8

Brand: UltraGauge Pages: 55

Brand: Vello Pages: 30

ORBISPHERE K1200

Brand: Hach Pages: 104

Brand: Metra Electronics Pages: 12

Brand: Halfords Pages: 4

MEDIA WIRELESS DESKTOP 800 -

Brand: LABTEC Pages: 12

Brand: handi quilter Pages: 2

Brand: Home Accents Holiday Pages: 2

Brand: Metra Electronics Pages: 4

REARSIGHT OnStar 250-8822

Brand: Rostra Pages: 2

Brand: Cerlic Pages: 20

Brand: TecnoVideo Pages: 4

Brand: Datalogic Pages: 40

Brand: Ohlins Pages: 4

Brand: Racelogic Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands