Fabtech FTS24084BK Installation Instructions Manual Download

Page: 3 / 31

- PARTS LIST -

FT50356

HARDWARE KIT

Qty.

Description

Location

1/2"-13 x 1 1/2" Bolt

Front Crossmember

1/2"-13 C-Lock Nut

----------------

1/2" SAE Flat Washer

----------------

1/2" Split Washer

----------------

12mm x 1.50 x 50mm Bolt

----------------

12mm Flat Washer

----------------

9/16"-12 x 4" Bolts

Front Lower Links

9/16"-12 C-Lok Nut

----------------

9/16" SAE Flat Washers

----------------

7/16"-14 x 3 1/2" Bolt

Front Upper Link

7/16"-14 C-Lock Nut

----------------

7/16" SAE Flat Washer

----------------

9/16"-12 x 3" Bolt

Front Trac Bar Bracket

9/16"-12 C-lock Nut

----------------

9/16" SAE Flat Washer

----------------

1/2"-13 x 3" Bolt

Front Sway Bar End Link

1/2"-13 C-Lock Nut

----------------

1/2"SAE Flat Washer

----------------

1/2"-13 x 1 1/2' Bolt

Front Lower Sway Bar Bracket

1/2"-13 C-Lock Nut

----------------

1/2" SAE Flat Washer

----------------

5/16"-18 x 1" Bolt

Front Sway Bar Rtnr

5/16"-18 C-Lock Nut

----------------

5/16" SAE Flat Washer

----------------

1/2"-13 x 2 1/2" Bolt

Front Shock

1/2"-13 C-Lock Bolt

----------------

1/2" SAE Flat Washer

----------------

1/2' USS Flat Washer

----------------

1/2"-13 x 3 1/2" Bolt

Front Bumpstop

1/2"-13 C-Lock Nut

----------------

1/2" SAE Flat Washers

----------------

1/4"-28 Grease Fitting

----------------

7/8” Lock Washer

Pitman Arm

FT50357

HARDWARE KIT

Qty.

Description

Location

1/2"-13 x 1 1/4" Bolt

Rear Link Pockets

1/2"-13 C-Lock Nuts

----------------

1/2" SAE Flat Washer

----------------

1/2" USS Flat Washer

----------------

1/2" Split Washer

----------------

7/16"-14 x 1" Bolt

Rear Shock Mount

7/16" SAE Flat Washer

----------------

7/16" Split Washer

----------------

1/2"-13 x 2 3/4" Bolt

Rear Shocks

1/2"-13 C-Lock Nut

----------------

1/2" SAE Flat Washers

----------------

9/16"-12 x 4 1/4" Bolt

Rear Lower Links

9/16"-12 C-Lock Nut

----------------

9/16" SAE Flat Washer

----------------

9/16"-18 x 3" Bolt

Rear Trac Bar

9/16"-18 C-Lock

----------------

9/16" SAE Flat Washer

----------------

3/8"-16x1" Bolt

Rear Trac Bar Bracket

3/8"-16 C-Lock Nut

----------------

3/8" SAE Flat Washer

----------------

1/4"-20x1" Bolt

Driver Rear Brake Line Bracket

1/4"-20 C-lock Nut

----------------

1/4" SAE Flat Washer

----------------

1/4"-20 x 1" Bolt

E-Brake Cable Bracket

1/4"-20 C-Lock Nut

----------------

1/4" SAE Flat Washer

----------------

3/8"-16 x 1" Bolt

Bump Stop Bracket

3/8"-16 C-Lock Nut

----------------

3/8" SAE Flat Washer

----------------

1/4"-28 Grease Fitting

----------------

8" Zip Ties

----------------

- TOOL LIST -

Required Tools (Not Included)

Floor Jack
Jack Stands
Torque Wrench
Pitman Arm Puller

Die Grinder w/Abrasive Disc
MIG Welder
Assorted Metric and S.A.E sockets, and wrenches

3 of 31

Summary of Contents for FTS24084BK
































Search results

Summary of Contents for FTS24084BK

Reviews:

Related manuals for FTS24084BK

Brands by name

Popular brands

Fabtech FTS24084BK, Installation Instructions Manual

Search results

Summary of Contents for FTS24084BK

Reviews:

Related manuals for FTS24084BK

Brands by name

Popular brands