FAAC E124, Rapid Manual

Page: 22 / 24

21
ENGLISH
SIGNALLING ERRORS AND ALARMS
In case of ERRORS (conditions that stop gate operation) or ALARMS (conditions that do not compromise gate operation) it is possible to see
the number related to the warning.
These warnings will disappear in the following cycle only if the situation causing them is removed.
:KHQWKHUHLVDQ(5525WKH$/$50/('ZLOOJRRQVWHDG\:KHQDQ$/$50LVWULJJHUHGWKH$/$50/('VWDUWVWRÀDVK
By simultaneously pr and - the display will show corresponding error number.
N° ERROR SOLUTION
0 1
Board broken Replace the board
02
Thermal protection active Wait for the board to cool down, check for overloads
03
Motor 1 faulty
Check that the motor works and that the wiring is not interrupted or damaged
04
Motor 2 faulty
0 5
Invalid SETUP Repeat board SETUP
0 8
BUS-2EASY device error Ensure that no two pairs of devices have the same address.
0 9
BUS-2EASY output
short-circuit
Check the connections of the connected and entered
BUS-2EASY devices
1 0
Motor 1 limit switch error Check the limit switch connections for motor 1
1 1
Motor 2 limit switch error Check the limit switch connections for motor 2
1 2
BUS-2EASY call Ensure that the BUS devices are operating correctly and, if necessary, repeat BUS device acquisition
1 3
FAIL SAFE Check that the safety devices (photocells) are operating correctly
1 4
Configuration error Check that the board is configured correctly (basic and advanced programming) and, if necessary, repeat SETUP
15
Movement timeout reached
Check that the motors are blocked; check that any limit switches are activated correctly and that the mechanical stops
are present.
16
Deep sleep The board is in advanced energy-saving mode. No action required.
1 7
Motor 1 encoder fault Check the connections or replace motor 1 encoder
1 8
Motor 2 encoder fault Check the connections or replace motor 2 encoder
1 9
Incorrect memory data Repeat BUS-2EASY device entry and/or re-program the board
4 5
Battery operation No action required.
9 3
High absorption at +24V Check that absorption by the accessories connected is within permitted limits
N° ALARM Solution/Description
2 0
Obstacle on MOTOR 1 (only with en-
coder)
Remove any possible obstacle on leaf 1
2 1
Obstacle on MOTOR 2 (only with en-
coder)
Remove any possible obstacle on leaf 2
22
MOTOR 1 current limited Check the force set on motor 1
23
MOTOR 2 current limited Check the force set on motor 2
2 5
LOCK 1 output short-circuit Remove the cause of the short-circuit
2 6
LOCK 2 output short-circuit Remove the cause of the short-circuit
2 7
Nr. of consecutive obstacles exceeded
during opening Remove any possible obstacle.
Should the problem persist, repeat SETUP
2 8
Nr. of consecutive obstacles exceeded
during closing Remove any possible obstacle.
Should the problem persist, repeat SETUP
3 0
XF radio code memory full
Cancel the radio codes that are not being used using the PC program or use an additional DEC/MINIDEC/
RP module
3 1
Tampering alarm
Movement was performed with automation in status
St
=
00
or
01
. Perform a manoeuvre cycle.
32
Emergency active Check that the emergency input is not active (configuration only possible from PC/Mac)
3 5
TIMER active and TIMER function operating: TIMER function is operating
4 0
Service request Contact the installer for maintenance
5 0
The HOLD POSITION is operating (active
on PC/MAC )
HOLD POSITION function is operating
6 0
TIMER active and error in TIMER data Reload a correct TIMER configuration with the PC/MAC programme
6 2
Loss of time and date on the board (only
if the TIMER is operating)
Reload the time and date with the PC/MAC programme and replace the BAT1 - CR2032 buffer battery
6 3
JOLLY TIMER is activated JOLLY TIMER is enabled by terminal board J3
6 4
TIMER DISABLED is operating TIMER is disabled by terminal board J3