background image

3

2

Safety Precautions

* Please review the content below to ensure safe and precise product usage.

Precautions

Neglect to follow directions can result
in death or serious injury.

Neglect to follow directions can result
in injury or material loss.

Warning

Caution

Do not place the product near a heat source (e.g.
heater) or source of moisture (e.g. aquarium,
humidifier).

It may cause product 

malfunction and/or fire.

Do not subject the product to any heavy shock
such as striking with a 
hard object 
(e.g. hammer, etc.).

It may cause product 

malfunction, electric
shock, and/or fire.

Do not allow water or other liquid to enter the
product interior.

It may cause product electric 

shock and/or fire.

Do not allow water to enter the camera interior
when cleaning.

It may result in electrical 

shock and/or fire.

Do not disassemble, install, or repair this product
on your own accord.

Contact the service center for any repair needs.
Unauthorized handling 
may cause product 
malfunction, electric 
shock, and/or fire.

If the product emits a peculiar noise, odor, and/or
smoke, immediately lower the circuit breaker
connected to the electric heater switch 
(ONT product connection) 
in the power cabinet panel, 
and then contact the 
service center.

Beware the risk of 

electric shock 
and/or fire.

Do not hang from or pull on the installed\ product.

Take special care to prevent 

such abuse by small 
children as injury may 
occur.

Make sure to pass the user manual onto the new
home owner/tenant when moving.

It can prevent any product misuse by the new

home owner/tenant.

Do not use pins or any sharp, pointy objects to
press buttons or to insert into holes.

It may cause product electric shock and/or fire.

Do not clean using wet cloths or volatile
substances (e.g. alcohol, benzene, thinner).

It may cause product electric shock and/or fire.

After receiving service, ask the service representative to perform a safety inspection.

Be careful when standing up after sitting under
the installed product.

Head injuries may occur 

from any impact with 
the installed product.

Preface

Warning

Warning

Caution

Summary of Contents for SHT-330XM/EN




















Reviews: