Note
Names and Functions
5
▶
▶
Interphone (SHT-IPE200/EN: Optional)
4
▶
▶
Product - Household unit
1
2
3
4
5
6
7
8
9
0
#
HOME INTERPHONE
SHT-1100
① Handset
This is used to communicate with a visitor outside
the entrance or the common entrance or make
calls to the interphone.
② LCD
screen
This shows the visitor's image.
③ POWER
indicator
This lamp turns red when the power is normal
and blinks in communication failure.
④ DOOR
indicator
When doorbell is connected, this lamp blinks if the
bell rings.
⑤ SET
button
This button is used to change various settings
(e.g. Bell sound, call volume, screen brightness,
initialization, etc.)
⑥ +/-
button
This is used to adjust bell sound, call volume and
screen brightness.
⑦ Speaker
This is used to output bell sound or voice during
communication with a visitor outside the entrance
(doorbell)/common entrance or when making a
call to the interphone.
⑧ Power
switch
This is used to turn the power on/off.
⑨ Interphone
button
This is used to make calls to the interphone.
⑩ Record/Replay
button
This is used to store images on the screen or play
stored images.
⑪ Door Open[release]
button
This is used to open the entrance/common
entrance during a call.
⑫ Call
button
This is used to check the status outside the
entrance, answer an incoming call with the
handset picked up or to make a speakerphone
call.
⑬ Microphone
This is used to make a call with a visitor outside
the entrance/common entrance or to the
interphone.
① Call
button
This is used to call the household unit from the
interphone or answer an incoming call with the
handset picked up.
② Open
button wih LED lamp
This is used to open the door with an incoming
call from the entrance lobby or during a call with a
visitor at the entrance lobby.
[Indication of LED lamp]
- RED blinking : before ID setting
- RED light : complete ID setting
- GREEN blinking : incomming/out going a call
- GREEN light : during a call
③ Handset
This is used to make a call.
④ Bell
Adjuster
This is used to adjust bell volume.
It can adjust both call volume and melody
volume.
SHT-3305XM
1
4
5
6
7
8
9
10
11
12
13
2
3
Preparation
Chapter
1
SLAVE3
DOOR1
DOOR2
LOCK2
LOCK1
SLAVE2
SLAVE1
JTAG1
BELL_1
UART1
J1
JTAG1
SLAVE
MS
ISP
Master
Interphone
6
5
4
3
2
1
6
5
4
3
2
1
1
2
3
Initial Setting for Interphone ID
1. Insert or remove the jumper on the bottom of
SHT-IPE200/EN for desired Interphone ID setting
as below;
JTAG1
SLAVE
MS
1
2
3
Pin1~3 OFF
1
2
3
Pin1-2 ON
1
2
3
1
2
3
1
2
3
Pin2-3 ON
Slave 1
Slave 2
Slave3
1
2
3
2. Connet to SLAVE1~3 port on the SHT-3305’s
bottom and SHT-IPE200/EN’s bottom by using
ext. haness(6 pins).
OPEN LED lamp will start blinking a few seconds, then
lighted when Slave ID is set to correctly.
If OPEN LED is blink continually, recheck each jumpers
of SHT-IPE200/EN.
Summary of Contents for SHT-330XM/EN
Page 1: ...GC68 00874A ED 01...
