EZ-ACCESS PATHWAY HD Code Compliant Modular Access System Installation Manual Download

Page: 8 / 92

PATHWAY HD Code Compliant Modular Access System Installation Manual

Page 8 of 92

PLATFORMS AND PLATFORM HANDRAIL OPTIONS, CONT’D.

RESTING PLATFORM WITH TWO-LINE*

PLATFORM WITH PICKETED GUARDS*

*FEET & LEGS SHOWN FOR CONTINUITY (ORDERED SEPARATELY)

KEY PLATFORM COMPONENTS

PHDCPCPR – CORNER POCKET COVER PAIR

PHDCPCD – CORNER POCKET COVER, DOUBLE, 1 EA.

PHDPPC – CONNECTOR PLATFORM TO PLATFORM

ADDITIONAL COMPONENTS FOR RAMPS & PLATFORMS

PHDSLxxPR – SUPPORT LEGS WITH FEET (PAIR)

PHDXB36 & PHDXB736 – CROSS BRACE

•

PHDXB36 USED ON 5’

& 6’ PLATFORM

SIDES & RAMPS

•

PHDXB736 USED ON

7’ PLATFORM SIDE

XX DENOTES USABLE

LENGTH (LENGTHS

AVAILABLE 10”

THROUGH 112")

Summary of Contents for PATHWAY HD Code Compliant Modular Access System





























































































Search results

Summary of Contents for PATHWAY HD Code Compliant Modular Access System

Reviews:

Related manuals for PATHWAY HD Code Compliant Modular Access System

Brands by name

Popular brands

EZ-ACCESS PATHWAY HD Code Compliant Modular Access System, Installation Manual

Search results

Summary of Contents for PATHWAY HD Code Compliant Modular Access System

Reviews:

Related manuals for PATHWAY HD Code Compliant Modular Access System

Brands by name

Popular brands