manualshive.com logo in svg

Extron electronics MKP 3000, User Manual, Page: 5 / 51

Share
Download
Extron electronics MKP 3000 User Manual Download Page 5

MKP 3000 Remote Control Panel • Quick Start Guide

Quick Start Guide — MKP 3000, cont’d

i

MKP 3000 Remote Control Panel • Table of Contents

Chapter 1 • Introduction

.......................................................... 1-1

About this Manual

................................................................ 1-2

About the MKP 3000 Remote Control Panels

......... 1-2

Setup examples ...................................................................... 1-2
RS-232 connection to the switcher ....................................... 1-3
Ethernet connection to the switcher ................................... 1-3
Application diagram .............................................................. 1-4

Chapter 2 • Installation

............................................................. 2-1

MKP Installation Overview

............................................... 2-2

UL Requirements for Wall Box Installation

............. 2-3

Installation Procedures

....................................................... 2-3

Preparing the site and installing the mounting bracket
(mud ring) or wall box .......................................................... 2-4
Mounting the MKP to the mounting bracket (mud ring)
or wall box ............................................................................. 2-7

Rear Panel and Side Panel Connections

.................... 2-8

Control connections ............................................................ 2-10

RS-232 cable termination .............................................. 2-12
TP cable termination ..................................................... 2-12

Power supply wiring ............................................................ 2-14

Mounting

 

the MKP 10 MAAP

......................................... 2-15

Chapter 3 • Local Operation

.................................................. 3-1

Front Panel Controls and Indications

......................... 3-2

Front Panel Operations

....................................................... 3-3

Changing the tie mode ......................................................... 3-4
Creating ties ........................................................................... 3-4

Creating a tie in matrix mode (default) ......................... 3-4
Creating a tie in input-only mode .................................. 3-6
Deselecting a tie .............................................................. 3-7

Viewing ties ........................................................................... 3-8
Selecting a preset .................................................................. 3-9
Adjusting the audio output .................................................. 3-9
Viewing and configuring the IP and MKP setup
parameters ........................................................................... 3-10

Host control port setting and pass-through
communications ............................................................. 3-12

Setting the LCD window backlighting ............................... 3-13
Setup procedures diagram .................................................. 3-13
Control panel security lockout (executive mode) .............. 3-15

QS-2

Step 10

Program the control panel with the size of the connected switcher

.

See “System Settings page” in chapter 5, “HTML Operation.”

Step 11

Use the control panel to select inputs and outputs

.  See “Front Panel

Operations” in chapter 3, “Local Operation.”

Table of Contents

im Vertrieb von

            CAMBOARD Electronics

www.camboard.de

Tel. 07131 911201
Fax 07131 911203

[email protected]

Summary of Contents for MKP 3000




















































Reviews:

No comments