MKP 3000 Remote Control Panel • SIS
™
Operation
MKP 3000 Remote Control Panel • SIS
™
Operation
SIS
™
Operation, cont’d
X11
= Baud rate
300, 600, 1200, 1800, 2400, 3600, 4800,
9600 (default), 14400, 19200, 28800,
38400, 57600, or 115200
X12
= Parity (1st character only)
O
dd,
E
ven,
N
one (default),
M
ark,
S
pace
X13
= # of data bits
7, 8 (default)
X14
= # of stop bits
1 (default), 2
X15
= Input or output number
0 through 999
X16
= Name
11 characters maximum for inputs
and outputs
12 characters maximum for presets
24 characters maximum for MKP
name.
Upper and lower case alphanumeric
characters and
“ ” + – : = /
and
spaces are valid.
The following characters are invalid in the name:
+ ~ , @ = ‘ [ ] { } < > ’ “ ; : | \
and
?
.
X17
= Preset number
X18
= Default name
Factory default name
(combination of the model name
+ last 3 pairs of MAC address).
X19
= Time and date (set)
MM/DD/YY-HH:MM:SS
where:
MM = month: 01 (Jan.) — 12 (Dec.)
DD = day: 01 through 31
YY = year: 00 through 99
HH = hour: 00 through 24
MM = minutes: 00 through 59
SS = seconds: 00 through 59
X20
= Time and date (read)
Day,•DD•Mmm•YYYY•HH:MM:SS
where:
Day = weekday: Mon through Sun
DD = day: 01 through 31
Mmm = month: Jan through Dec
YYYY = year: 2000 through 2099
HH = hour: 00 through 24
MM = minutes: 00 through 59
SS = seconds: 00 through 59
X21
= GMT offset
–12.0 t14.0. Hours and
minutes removed from GMT
4-7
Symbol definitions
= CR/LF (carriage return/line feed) (0x0D 0A)
•
= space
X1
= On/off status
0 = off/disable
1 = on/enable
X2
= RS-232 port number
1 = host
2 = switcher
X3
=
n
= –1= redirect serial port data from the specified port to allow
for a transparent pass through mode. The response is returned
with leading zeroes.
n
= the maximum number of serial ports that the IP link supports.
X5
is verified at this port.
X4
= Time (in 10 ms increments) to wait for receive data before
releasing the port to another source (min = 1 [10 ms],
maximum = 32767 [32.767 seconds], default = 10 [100 ms]).
X5
= Numerical value (
nnnn
) to set
L
(length of message to receive) or
assign as a
D
(delimiter).
L
= number of byte count (min = 0, max = 32767, default = 0).
D
= decimal number for ASCII character (min = 0,
maximum = 00255, default = 00000L).
The numeric value directly precedes the identifier; for example:
X5
= “3L”
to specify a 3-byte length or
X5
= “10D” to specify an ASCII delimiter of
0A. The identifier, “L” or “D” is case sensitive and must be uppercase.
X6
= Firmware version
Bootstrap version
(x.xx)
X7
= Verbose firmware version-description-upload date/time. See
page 4-10.
X8
= Voltage 1 (3.3 V), Voltage 2 (12.0 V),
Temperature (degrees Fahrenheit)
(
xxx.xx
), Voltage 3 (5.0 V)
X9
= Verbose/response mode
0 = no password assigned
1 = verbose mode
2 = tagged responses for queries
3 = 1 and 2 (verbose and tagged)
The default
X9
value is 0 for telnet and 0 for RS-232.
If tagged responses are enabled, all read commands return the constant
string plus the data, the same as setting the value. For example, the MKP
responds
Ipn•
X18
to the
Esc
•CN
command.
X10
= Security level
0 = clear/none
11 = user password assigned
12 = administrator password assigned
4-6
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203