manualshive.com logo in svg

Extron electronics MKP 3000, User Manual, Page: 13 / 51

Share
Download
Extron electronics MKP 3000 User Manual Download Page 13

MKP 3000 Remote Control Panel • Installation

MKP 3000 Remote Control Panel • Installation

Installation, cont’d

3

1

2

4

5

6

Figure 2-7 — MKP 3000 MAAP rear panel

1

LAN (Ethernet) port — 

If desired, connect a Category (CAT) 5e

or higher (network) cable between this
connector and either the matrix switcher to be
controlled or to an Ethernet local area network
(LAN).  See “TP cable termination,” later in
this chapter, to properly wire the RJ-45
connector for your application.

Ethernet connection indicators

 

— 

The Link and Activity LEDs

on the LAN port indicate the status of the Ethernet connection.
The green Link LED indicates that the MKP is properly
connected to an Ethernet LAN.  This LED should light steadily.
The yellow Activity LED indicates transmission of data packets
on the RJ-45 connector.  This LED should flicker as the MKP
communicates.

2

Power connector — 

Plug the included external 12 VDC power

supply into this 2-pole captive screw connector.  See “Power
supply wiring,” on page 2-14, to wire the connector.

3

Remote Keypad port — 

If desired, plug the optional

MKP 10 MAAP remote keypad into this 10-pin connector, using
the cable included with the MKP 10 MAAP.

4

Host RS-232 port — 

If desired, connect a host computer or

control system to this 3-pole, 3.5 mm, RS-232 connector
(figure 2-8).

Pin Function

TX

RX

Gnd

Tr

a

n

s

mit d

a

t

a

Receive d

a

t

a

S

ign

a

l gro

u

nd

Tx

HO

S

T

R

S

-2

3

2

S

WITCH

R

S

-2

3

2

Rx

GND

Tx

Rx

GND

Figure 2-8 — RS-232 connector

RJ-45

Port

Link

LED

Activity

LED

2-9

3

.

Mount the MKP’s faceplate to the mud ring or wall box
with machine screws (figure 2-5).

Extr

on

MK

P 30

00

I/O

SE

LE

CT

PO

W

ER

RE

SE

T

Figure 2-5 — Mounting the MKP to the wall box

4

.

Reconnect the power supply and restore power.

Rear Panel and Side Panel Connections

All connectors are on the rear or side of the MKP (figure 2-6 and
figure 2-7).  These connectors are inaccessible once the MKP is
installed.

GND

12 V

REMO

TE

KEYP

AD

POWER

.5A MAX

Tx

HOST

RS-232

SWITCH

RS-232

Rx

GND

Tx

Rx

GND

GND

12 V

REMO

TE

KEYP

AD

PO

WER

.5A MAX

Tx

HOST

RS-232

SWITCH

RS-232

Rx

GND

Tx

Rx

GND

3

1

2

4

5

Figure 2-6 — MKP 3000 rear and side panels

2-8

im Vertrieb von

            CAMBOARD Electronics

www.camboard.de

Tel. 07131 911201
Fax 07131 911203

[email protected]

Summary of Contents for MKP 3000




















































Reviews:

No comments