MKP 3000 Remote Control Panel • Local Operation
MKP 3000 Remote Control Panel • Local Operation
Local Operation, cont’d
Control panel security lockout (executive mode)
The front panel security lockout limits the MKP’s front panel
operation to input selection, output selection, preset selection,
and volume control only, depending on the MKP’s mode (IP
address modification is locked).
The MKP 3000 provides the following three levels of front panel
security lockout (executive modes):
Panel Locked mode
— All front panel controls are locked.
Selections and setup cannot be performed from the front
panel.
User mode
— Front panel operation is limited to input, output,
and preset selection, and volume control. The panel
configuration, IP, and switcher addressing functions are
locked.
Administrator mode
(default) — All front panel controls are
available.
For an MKP 3000 without an MKP 10 MAAP connected,
1
.
Press and
hold
all four front panel buttons (figure 3-7)
until all four buttons blink and then light amber, and the
LCD displays the name of the executive mode that was
entered (approximately 3 seconds).
•
Administrator mode
— The LCD window briefly
displays “Admin Mode,” then returns to what was
previously displayed.
•
User mode
— The LCD window briefly displays
“User Mode,” then returns to what was previously
displayed.
•
Panel Locked mode
— The LCD window displays
“Panel Locked” until the executive mode is changed.
2
.
If necessary, repeat step
1
until the desired executive mode
is entered.
I / O
SELECT
INPUT TAKE
OUTPUT
VIDEO
GREEN
AUDIO
RED
Simultaneously press and
hold
all buttons for 3 seconds.
All buttons blink
and then
li
g
ht amber
.
Release the buttons.
Figure 3-7 — Control panel lockout
3-15
SELECT
SELECT
IP 192.168
add 254.253
>
IP 192.168
add 254.253
>
IP 192.168
add 254.253
>
IP 192.168
add 254.253
IP 192.168
add 254.253
>
>
Sub 255.255
net 000.000
>
Sub 255.255
net 000.000
>
Sub 255.255
net 000.000
Sub 255.255
net 000.000
>
>
Gate 000.000
way 000.000
>
Gate 000.000
way 000.000
>
Gate 000.000
way 000.000
Gate 000.000
way 000.000
>
>
Host 000.000
IP 000.000
>
Host 000.000
IP 000.000
>
Host 000.000
IP 000.000
Host 000.000
IP 000.000
>
>
Passthrou
g
h
Disabled
>
Passthrou
g
h
Enabled
>
Connection
Primary
>
Connection
Secondary
>
SELECT
Backli
g
ht
30 Seconds
SELECT
INPUT
INPUT
INPUT
INPUT
INPUT
INPUT
INPUT
INPUT
TAKE
TAKE
OUTPUT
OUTPUT OUTPUT
OUTPUT OUTPUT
OUTPUT OUTPUT
OUTPUT OUTPUT
INPUT
>
Tie Mode
Matrix
>
>
Tie Mode
Input Only
The LCD shows MKP 3000’s
IP address. The caret (>)
shows the editable octet.
Press and
hold
these buttons for
2 seconds until they light amber.
This knob changes the
editable octet/field.
MKP 3000’s
IP Address
MKP 3000’s
Subnet Mask
MKP 3000’s
Gateway
Address
Matrix
Switcher’s
IP Address
Connection
Priority
Backlight
Duration
Host Control
Setting
2
Press button or rotate
the Select knob to toggle
between the Enabled and
Disabled selections.
Press button 3 to cycle through the
selected ( > ) and editable octets.
3
Press button or rotate
the Select knob to toggle
between the Primary and
Secondary selections.
Rotate the Select knob to
set the LCD backlight to
always on (0) or to timeout
after 001 to 255 seconds.
Press and release button to execute
all of the settings and exit Set-up mode.
Press b
u
tton 3 to cycle through the displa
y
ed and
editab
le addresses and to reach the MKP setup settings
.
2
4
3
4
Tie Mode
SELECT
OUTPUT
OUTPUT
Press button or rotate
the Select knob to toggle
between the Matrix and
Input Only selections.
3
3
3
Figure 3-6 — Selecting setup parameters
3-14
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203