MKP 3000 Remote Control Panel • Local Operation
MKP 3000 Remote Control Panel • Local Operation
Local Operation, cont’d
R
R
R
R
R
R
R
R
R
6
s
econd
s
LED fl
as
he
s
twice
.
3
s
econd
s
LED fl
as
he
s
once
.
Pre
ss
a
nd
hold
the Re
s
et
bu
tton.
Rele
as
e, then
immediately
pre
ss
a
nd
rele
as
e
a
g
a
in.
Rele
as
e, then
immediately
pre
ss
a
nd
rele
as
e
a
g
a
in.
Rele
as
e, then
immediately
pre
ss
a
nd
rele
as
e
a
g
a
in.
Ab
s
olute
(mode 5)
Re
s
et
Pre
ss
a
nd
hold
the Re
s
et
bu
tton.
IP
S
y
s
tem
(Mode 4)
Re
s
et
Pre
ss
a
nd
hold
the Re
s
et
bu
tton.
Event
s
(Mode
3
)
Re
s
et
9
s
econd
s
LED fl
as
he
s
three time
s
.
Figure 3-8 — Performing soft resets
2
.
Release the Reset button and then immediately press and
release the Reset button again. Nothing happens if the
second momentary press does not occur within 1 second.
Performing a hard reset
The hard reset restores the MKP to the original factory default
firmware configuration and erases all user-installed software or
firmware. (A hard reset does not perform all possible MKP
reset functions.)
CAUTION
Ensure that you have backed up any locally-created
HTML, JavaScript, or other files that you have
uploaded to the MKP’s user file space
before
you
perform the hard reset. A hard reset
will erase
all
locally-created files from the MKP.
Perform a hard reset as follows:
1
.
If necessary, turn off power to the switcher.
2
.
Press and
hold
the Reset button on the rear panel
while
you apply AC power to the MKP (figure 3-9).
3-17
3-16
When you unlock the control panel, the MKP 3000
enters setup mode. Make changes if desired and then
press the Take button to exit.
For an an MKP 3000 connected to an MKP 10 MAAP:
1
.
On the MKP 10 MAAP, press and
hold
the 1, 3, Back, and
Cancel buttons until the MKP 3000 LCD window displays
the name of the executive mode that has been set
approximately 3 seconds). (Admin Mode and User Mode
are displayed briefly; Panel Locked remains displayed.)
2
.
If necessary, repeat step
1
until the LCD window indicates
the mode you want.
Rear Panel Resets
Performing soft resets
The remote control panel has three soft resets available that
restore various tiers of MKP settings to their default settings.
•
Events (mode 3) reset —
Restarts the communications
and control events.
•
IP system (mode 4) reset —
IP system reset resets most IP
protocols to their default settings.
IP system reset clears the Internet protocol (IP) settings,
but does not reset the target address, the host control
setting, the priority setting, or any user-loaded files.
•
Absolute (mode 5) reset —
Performs all of the system
reset functions
and
clears the MKP’s IP address to
192.168.254.253 and its subnet mask to 255.255.0.0. This
function is identical to the SIS command
Esc
ZQQQ
(see
chapter 4, “SIS
™
Operation”).
Perform a soft reset of the MKP as follows:
1
.
Press and
hold
the Reset (R) button until the Reset LED
blinks off once (events reset), twice (IP system reset), or
three times (absolute reset) (figure 3-8).
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203